- PSDR - mailman.hamwan.org

Baldi's back on UPS power
by Bart Kus 02 Oct '19

02 Oct '19

We've had an internal thread + coordinated response on netops@ about this, but I don't think anyone's notified the PSDR list yet. Here's the current Baldi power status: The UPS has been on battery for 16 hours 6 minutes 48 seconds. There are 28 hours 20 minutes of runtime remaining. The time remaining estimate may or may not be accurate. We have shut down unnecessary loads. Camera remains operational. I also attempted to setup APC PowerChute automatic power failure -> server shutdown software. The APC appliance didn't quite work, and I need to take a 2nd pass at configuring it. It is not known at this time if this is another mains line cut, or a failure of a generator that may have been deployed. --Bart

2 2

North end of Camano Island connection/signal information
by James Lehr 02 Oct '19

02 Oct '19

Hi everyone. My name is James Lehr and I'm really excited about what ya'll are doing here. I'm a general licence holder, an electrician, and an industrial controls and automation technician. I live on the north end of Camano Island about 3 miles west of Stanwood. It looks like I'm a candidate for connection from everything I've read and looked at. I'd like to start a conversation about getting on and also about getting involved in helping with.... well everything. If it would be easier to have a conversation over a phone call let me know I'll put my number up. Anyhow, I'm deep into the tech of everything I can soak up so this, what ya'll are doing sounds amazing. Regards, James KJ7EXW

3 2

Now accepting proposals for kick-ass repeaters
by Bart Kus 27 Sep '19

27 Sep '19

Hello, I have recently finished upgrading the power system @ the Haystack site (4100ft, near Sultan). With the new found power budget, I'd like to get some more interesting things on the air. Space is limited, and I'd like to give preference to new/unique/high-quality/impressive projects. Here are a couple of potential ideas: 1) I'd like more repeater coverage through the Hwy 2 mountain pass. Present coverage drops off after Grotto, but it picks up again around Berne, due to mountain peak refraction. It might be interesting to stand up a 6m repeater that would bend around the mountains a bit better, and maybe tie it to DMR or something, and run it with decent enough power (300W?) that it's heard. 2) It might be interesting to have an international repeater (when the band is open) on 10m. Again, possibly tied with DMR, and again with some beefy power output. Standby power needs to be low, but transmit power can be high. I'm expecting ham applications to have a very low duty cycle. Please reply to me (not list) with what you think might be interesting up there, or if you've got the skills + gear + budget to pull off the 2 ideas I threw out here. Feel free to forward to other folks + lists, as I'd like to get the best possible ideas in front of me. Should be an interesting next few days. :) --Bart

1 0

Do I need a Cacti login to update my entry on the HamWAN live map?
by John Spady 22 Sep '19

22 Sep '19

Hello, I have had my first successful test of a HamWAN connection to Beacon Hill over my new condo network. I would like my user/client information to now appear on the live HamWAN map. I read that I can add my own information using Cacti but I don’t see how I can create my own login. Perhaps an admin has to enter information on my behalf? Can someone please let me know what I need to do to add my entry to the live map? Thank you. John Spady WA7UAR 206-465-6963 Sent from my iPhone ;-)

2 2

Re: [HamWAN PSDR] Baldi Power Outage
by Daniel Stevens 17 Sep '19

17 Sep '19

Thank you for the update Daniel Stevens KL7WM On Tuesday, September 17, 2019 Nigel Vander Houwen <psdr(a)hamwan.org> wrote: Hello All, Baldi is currently on battery power. The utility is aware of the outage. Currently the site remains at full capability. Thanks! Nigel _______________________________________________ PSDR mailing list PSDR(a)hamwan.org http://mail.hamwan.net/mailman/listinfo/psdr

2 2

Re: [HamWAN PSDR] Possibility of tower usage for nonprofit WISP?
by Pavel Kirkovsky 17 Sep '19

17 Sep '19

Several helpful replies so far but still no clarification on who manages the BawFaw tower and whether it's possible to use it for this. Any suggestions on who to ask next? ~~ Thanks, Steve! That sounds like a great resource and I'll see if I can get over there. > On Sep 11, 2019, at 1:36 PM, Steve Stroh <steve.stroh(a)gmail.com> wrote: > > Pavel: > > If you’re seriously considering starting a WISP, you should attend this event next month: > > http://www.wispa.org/Events/WISPAPALOOZA-2019-Summary <http://www.wispa.org/Events/WISPAPALOOZA-2019-Summary> > It’s a crash course in all things WISP. Including starting your own fiber network. > > Steve N8GNJ That's the unfortunate part — there's no ISP coverage and LTE service is spotty (T-Mobile says the tower is congested and the signal to the house is so spotty they can't actually consider it as having service). > On Sep 11, 2019, at 11:42 AM, KUN LIN <dnwk(a)linkun.info> wrote: > > Have you tried running home internet on some unlimited LTE plans? I have no trouble running my home internet this way. However, I don't know if you get good cell coverage at home. > Kun -Pavel KG7LZB

2 1

Re: [HamWAN PSDR] MikroTik mANT30 Dish antenna free to good home
by John G Parnell 17 Sep '19

17 Sep '19

The MikroTik dish has been tentatively spoken for, and there is long backup list - thanks for your interest & good luck. 73 - John K7HV

1 0

Re: [HamWAN PSDR] PSDR Digest, Vol 79, Issue 11
by Rod Johnson 17 Sep '19

17 Sep '19

The Issaquah Emcomm (ICST) could use it. ROD J -----Original Message----- From: psdr-request <psdr-request(a)hamwan.org> To: psdr <psdr(a)hamwan.org> Sent: Tue, Sep 17, 2019 12:38 PM Subject: PSDR Digest, Vol 79, Issue 11 Send PSDR mailing list submissions to psdr(a)hamwan.org To subscribe or unsubscribe via the World Wide Web, visit http://mail.hamwan.net/mailman/listinfo/psdr or, via email, send a message with subject or body 'help' to psdr-request(a)hamwan.org You can reach the person managing the list at psdr-owner(a)hamwan.org When replying, please edit your Subject line so it is more specific than "Re: Contents of PSDR digest..." Today's Topics: 1. MikroTik mANT30 Dish antenna free to good home (John G Parnell) 2. Baldi Power Outage (Nigel Vander Houwen) ---------------------------------------------------------------------- Message: 1 Date: Mon, 16 Sep 2019 16:50:26 -0700 From: "John G Parnell" <jparnell(a)igc.org> To: <psdr(a)hamwan.org> Subject: [HamWAN PSDR] MikroTik mANT30 Dish antenna free to good home Message-ID: <002601d56ce9$83da4fc0$8b8eef40$(a)igc.org> Content-Type: text/plain; charset="utf-8" Hello, I just realized that this list is for the W WA area, so I thought I would start here with this: Back in July, I ordered a MikroTik mANT30 dish antenna (with precise alignment mount) for my HamWAN installation. It arrived with the edge of the dish bent up AND the mount bent (!). I contacted the vendor and they sent another one and said they would send me a UPS label for the return. After 3 weeks, I emailed my contact and told them that if I didn't get the shipping labels, I would give it away. Well, it has been month with not a peep from them, so: I am offering up the antenna for free to someone who could use it. I bent the mounting frame tabs to fit the dish and cleaned up the edges of the dish as best I could with an adjustable wrench as a bending lever. The dish itself has maintained it's symmetry and I was able to bend the mounting tabs to match it, so it should be fully functional. Just to make sure, I assembled it and it looks fine, except for a bit of unevenness at the very edge of the dish. It is ready to mount a MikroTik radio (I juse the MikroTik RB912UAG-5HPnd). Here is a link to the dish's spec sheet: https://i.mt.lv/cdn/rb_files/mANT30-140526124123.pdf (it is the one on the bottom) I would prefer to pass this on to someone involved in Emcom activities who will actually use it - or someone helping someone else getting set up. Give me a call to arrange pickup, I will not ship it. I am located in NE Seattle in the Maple Leaf neighborhood, you can find my address in QRZ. 73, John, K7HV 206 947 0545

1 0

Baldi Power Outage
by Nigel Vander Houwen 17 Sep '19

17 Sep '19

Hello All, Baldi is currently on battery power. The utility is aware of the outage. Currently the site remains at full capability. Thanks! Nigel

1 0

MikroTik mANT30 Dish antenna free to good home
by John G Parnell 16 Sep '19

16 Sep '19

Hello, I just realized that this list is for the W WA area, so I thought I would start here with this: Back in July, I ordered a MikroTik mANT30 dish antenna (with precise alignment mount) for my HamWAN installation. It arrived with the edge of the dish bent up AND the mount bent (!). I contacted the vendor and they sent another one and said they would send me a UPS label for the return. After 3 weeks, I emailed my contact and told them that if I didn't get the shipping labels, I would give it away. Well, it has been month with not a peep from them, so: I am offering up the antenna for free to someone who could use it. I bent the mounting frame tabs to fit the dish and cleaned up the edges of the dish as best I could with an adjustable wrench as a bending lever. The dish itself has maintained it's symmetry and I was able to bend the mounting tabs to match it, so it should be fully functional. Just to make sure, I assembled it and it looks fine, except for a bit of unevenness at the very edge of the dish. It is ready to mount a MikroTik radio (I juse the MikroTik RB912UAG-5HPnd). Here is a link to the dish's spec sheet: https://i.mt.lv/cdn/rb_files/mANT30-140526124123.pdf (it is the one on the bottom) I would prefer to pass this on to someone involved in Emcom activities who will actually use it - or someone helping someone else getting set up. Give me a call to arrange pickup, I will not ship it. I am located in NE Seattle in the Maple Leaf neighborhood, you can find my address in QRZ. 73, John, K7HV 206 947 0545

1 0